Welcome to Voxel Factory!
Bowden Tube Pack for Ultimaker 2(+)/Ext, Ultimaker 3(+)/Ext, Ultimaker 2+ Connect and Ultimaker S3
1x 1266 bowden tube
2x 1069 collets
2x 1071 blue clamp clip
Ultimaker SKU: 1696
White OLED screen for Ultimaker 2 Go, Ultimaker 2, Ultimaker 2+ / Extended, Ultimaker 3 / Extended.
Ultimaker Part Number: 1252
Ultimaker Part number 2237
Axial Hot end cooling fan: 35x35x10
Works with: S5/S3/UM3/UM3X
Ultimaker Part Number : 2133 replaced with 215431
Thick grease to lubricate the lead screws of your 3D printers. Not to be used on smooth rods; use Unilube Lubricant instead.
Weight : 21.25g
This maintenance kit includes all the parts you need to perform maintenance on your Ultimaker 2+ or Ultimaker 2+ Extended :
1x Glass plate
1x Bowden tube
PT100 B glassfiber sensor
Heater cartridge 35W
Build plate clamp
Tube coupling collet
Hot end isolator
Olsson nozzles (0.40, 0.25, 0.60 and 0...
Get more out of your Ultimaker S5 with the Material Station. Load up to six spools of filament in a humidity-controlled, fully enclosed compartment. The station integrates with Cura to enable live spool switching for uninterrupted, hassle-free printing.
Key features :
Easy loading : front-facing loading for up to six spools of filament
This original USB stick from Ultimaker works wonders with the Ultimaker 3 (and its Extended version) as well as the Ultimaker 2+ Connect, Ultimaker S3 and Ultimaker S5 3D printers.
Capacity : 16 GB
Print Head Bearing Housing Assembly for the following Ultimaker printers :
Ultimaker 2 Extended+
Ultimaker 2 Go
Ultimaker 2 Extended
Print head PCB board compatible with UM3 and UM3 Extended not S series
UMK SKU: 2012
This is the official Ultimaker spare part for the printers such as the Ultimaker 2, Ultimaker 2 Go, and Ultimaker Extended printers that use the second generation (white) electronics boards.
This is not compatible with the Ultimaker Original, Ultimaker Original+, nor the Ultimaker 2+ or Extended+ printers.
Ultimaker SKU: 2225
Part cooling Radial Fan: 35X35X10
Works with: S5/S3/UM3/UM3X
Ultimaker part number : 2135
Replacement EPA E10 filter for the Ultimaker S5 Air Manager.
Filter replacement is recommended every 1500 print hours (approximately 1 year).
Ultimaker SKU 226752
SLIDING BLOCK 726 For Ultimaker S3UMK SKU 225739
Install this upgrade kit to turn your Ultimaker 2 in an up-to-date Ultimaker 2+.
Fully assembled print head
Geared feeder motor
Print head shafts
Ultimaker calibration card
Filament reel holder
Build plate clamps
The newest addition to Ultimaker's line of FFF printers, The Ultimaker 2+ Connect. A single nozzle printer with networking capabilities and a new touchscreen, the Ultimaker 2+ Connect is your reliable first step into our world of easy, remote 3D printing. Simply unbox and connect three components, and get started. This speedy setup even makes in...
Linear Bearings Compatible with 2/ 2+/2+ Extended/2+ Connect (LMUW6)
Ultimaker Part Number: 1065
The Ultimaker 3 Maintenance kit contains the most commonly used parts for maintenance or replacement on the Ultimaker 3 or Ultimaker 3 Extended. It can be purchased in addition to your Ultimaker and used as an overall maintenance kit, or it can be used for spare parts.
Below you can find an overview of all the parts that are included in the ma...
This silicon piece covers the print cores of your Ultimaker 3/3 Ext to prevent the build-up of material around the nozzles.
Ultimaker Part Number: c
For a smoother experience when printing with engineering materials (ABS, CPE / CPE+, PC) with your Ultimaker 3D printer, try the advanced 3D printing kit. Includes :
1 Front enclosure
25 Adhesion sheets
1 Adhesive applicator
1 Glass plate
UMB Cable for the Ultimaker Air Manager to connect to the Ultimaker S5
UM BUS CABLE L610 STRAIGHT/STRAIGHT
UMK SKU 212897
Sitting atop your Ultimaker 2+ Connect 3D printer, the Air Manager provides a closed, inside-out airflow throughout the printing process. Thanks to its E10 filter, up to 95% of ultrafine particles created while printing are captured, resulting in a safer work environment.
Through Cura and the Ultimaker 2+ Connect, the Air Manager smartly adjusts...
Sitting atop your Ultimaker S5 3D printer, the Air Manager provides a closed, inside-out airflow throughout the printing process. Thanks to its E10 filter, up to 95% of ultrafine particles created while printing are captured, resulting in a safer work environment.
Through Cura and the Ultimaker S5, the Air Manager smartly adjusts the airflow ins...
Pack of 25 self adhesive sheets to use on your Ultimaker glass build plate for optimal material adhesion. Recommended for engineering materials.
Compatible with UM2+/2+Ext/UM3/3+/3+Ext/S3/2+Connect buildplates.
Ultimaker SKU 2197